The 2026 Harley-Davidson® Street Glide® Limited is engineered as a full-size touring motorcycle with a focus on measurable performance, integrated systems, and long-distance functionality. The model combines a Milwaukee-Eight® VVT 117 engine, a 6-speed Cruise Drive® transmission, and a structurally reinforced steel chassis. Its overall length measures 103.3 inches, with a width of 40.7 inches and a height of 56.7 inches. The wheelbase is set at 64 inches, supporting directional stability and consistent handling across extended highway travel. The rake angle is 26 degrees, with a fork angle of 29.25 degrees and a trail measuring 6.7 inches. Seat height is 27.5 inches in a laden condition and 29.1 inches unladen, while ground clearance is rated at 5.9 inches.
Engine Configuration and Output Characteristics
The Milwaukee-Eight® VVT 117 engine uses a pushrod-operated overhead valve design with four valves per cylinder and hydraulic self-adjusting lifters. The bore measures 4.075 inches, and the stroke is 4.5 inches, producing a displacement of 117 cubic inches or 1,923 cubic centimeters. The compression ratio is set at 10.3:1, supporting efficient combustion and consistent output. The fuel system uses electronic sequential port fuel injection, which provides controlled fuel delivery across varying throttle conditions.
Engine output is rated at 106 horsepower at 4,600 rpm. Torque output is 131 pound-feet at 3,250 rpm, measured using J1349 standards. These figures indicate a power curve oriented toward low to mid-range operation, which supports steady acceleration and load-carrying capability. The lubrication system is a pressurized dry-sump configuration, which maintains oil circulation independent of crankcase storage. Air intake is handled by a washable fiberglass air cleaner, while exhaust gases are routed through a 2-1-2 dual exhaust system with tapered mufflers.
Drivetrain and Gear Ratio Structure
The drivetrain integrates a chain-driven primary system with a 34/46 ratio and a belt-driven final system with a 32/68 ratio. This configuration reduces maintenance requirements associated with traditional chain final drives while maintaining efficient power transfer. The clutch system is a mechanically actuated 10-plate wet clutch with assist and slip functionality. This design reduces lever effort during operation and moderates rear-wheel behavior during downshifts.
The 6-speed Cruise Drive® transmission provides a wide ratio spread for both acceleration and highway cruising. First gear is set at 9.593, while sixth gear is set at 2.875. Intermediate gear ratios are spaced at 6.65 for second, 4.938 for third, 4.0 for fourth, and 3.407 for fifth. This distribution allows the engine to operate at lower rpm during sustained travel, reducing mechanical strain and improving fuel efficiency during extended riding periods.
Frame Architecture and Structural Design
The frame uses a mild steel tubular construction with a two-piece stamped and welded backbone. Cast and forged junctions are incorporated to reinforce high-load areas, while twin down-tubes provide additional rigidity. The rear frame section is bolt-on and includes forged fender supports. Welding processes include MIG techniques to ensure structural consistency across joints.
The swingarm is constructed from mild steel using a two-piece drawn and welded design with forged junctions. This contributes to overall stability during acceleration and braking. The structural design prioritizes load distribution and resistance to flex, which is critical for a motorcycle with a running weight of 893 pounds. The as-shipped weight is 855 pounds, and the gross vehicle weight rating is 1,360 pounds. Front axle weight rating is 500 pounds, while the rear axle rating is 927 pounds.
Suspension System and Ride Control
Front suspension is managed by a 49 mm dual bending valve fork. This system is designed to improve damping response by controlling oil flow through variable bending elements within the fork assembly. Rear suspension uses dual adjustable emulsion shocks with 3 inches of travel. The left shock includes remote preload adjustment, while the right shock uses threaded preload adjustment. This configuration allows compensation for changes in rider weight, passenger load, and cargo.
Front suspension travel measures 4.6 inches. Rear travel measures 3 inches. These values are consistent with touring requirements that prioritize ride comfort and chassis control over aggressive suspension articulation. The system is tuned to absorb road irregularities while maintaining predictable geometry under load.
Wheels, Tires, and Contact Geometry
The 2026 Harley-Davidson® Street Glide® Limited is equipped with cast aluminum wheels. The front wheel has a diameter of 19 inches and a width of 3.5 inches. The rear wheel measures 18 inches in diameter and 5 inches in width. Tire specifications include a 130/60B19 M/C 61H front tire and a 180/55B18 M/C 80H rear tire, both from the Dunlop® Harley-Davidson® Series.
This tire configuration supports a stable front contact patch and a wider rear footprint for traction. The bias construction contributes to durability and load handling, which aligns with touring requirements. The wheel and tire combination is matched to the motorcycle’s weight distribution and intended riding conditions.
Braking System and Mechanical Control
The braking system uses dual floating rotors at the front and a fixed rotor at the rear. Front rotor diameter is 12.6 inches, with a thickness of 0.18 inches. The rear rotor measures 11.8 inches in diameter with a thickness of 0.28 inches. Calipers consist of 32 mm four-piston fixed units at the front and a single fixed unit at the rear.
Anti-lock braking is standard and works in conjunction with the mechanical components to prevent wheel lock during braking. The dual front brake configuration increases stopping capability, while the rear system contributes to overall balance. This setup is calibrated for a touring motorcycle that operates under varying load conditions.
Electrical System and Lighting Configuration
The electrical system includes a sealed, maintenance-free 12-volt battery rated at 28 amp-hours and 405 cold cranking amps. Charging is handled by a three-phase 58-amp system, producing up to 754 watts at 13 volts. The starting system uses a 1.6 kW electric motor with solenoid engagement.
Lighting is fully LED-based. The headlamp, tail, and stop lights, front signals, and rear turn signals all use LED technology. Auxiliary LED fog lamps are integrated into the lower fairings. This configuration provides consistent illumination and reduced energy consumption compared to traditional lighting systems.
A USB-C power outlet rated at 15 watts is located in the media storage compartment. An additional power outlet is integrated into the Tour-Pak®. These ports support device charging during operation.
Infotainment Interface and Connectivity Systems
The infotainment system operates on Skyline™ OS and uses a 12.3-inch full-color TFT display. The system integrates digital gauges, navigation, and media functions into a single interface. Audio output is rated at 50 watts per channel and is delivered through four speakers. Two speakers are positioned in the fairing, and two are mounted in the Tour-Pak®, each measuring 6.5 inches.
The system supports AM and FM radio. Media playback is available through USB-connected storage devices, including SD cards and flash drives. Bluetooth® functionality supports mobile phone integration, media playback, and headset connectivity. Apple CarPlay® compatibility is available in both wired and wireless configurations.
Navigation is embedded within the system and includes traffic and weather data through Wi-Fi connectivity. Vehicle information, such as air temperature, oil pressure, and engine idle temperature, is displayed within the interface.
Rider Assistance and Control Systems
The 2026 Harley-Davidson® Street Glide® Limited includes multiple electronic rider assistance systems designed to manage braking, traction, and low-speed stability. Anti-lock braking, electronic linked braking, traction control, drag-torque slip control, and vehicle hold control are all standard. Tire pressure monitoring is also included.
Cornering-specific enhancements expand these systems by adjusting performance based on lean angle. These include cornering-enhanced anti-lock braking, cornering-enhanced linked braking, cornering-enhanced traction control, and cornering drag-torque slip control. These systems monitor dynamic conditions and adjust braking force and engine output accordingly.
Vehicle hold control assists during incline starts by maintaining brake pressure when the rider releases the brake lever. This reduces rollback and simplifies control in stop-and-go conditions on slopes.
Fuel Capacity and Operational Range
Fuel capacity is rated at 6 gallons, with a reserve indicator activated at approximately 1 gallon remaining. Fuel economy is estimated at 45 miles per gallon under combined city and highway conditions. This supports extended riding intervals between refueling stops, which is a key consideration for touring motorcycles.
Fluid capacities include 5 quarts of engine oil with filter, 1 quart of transmission fluid, and 1.1 quarts for the primary chain case. Coolant capacity is 0.82 quarts. These values define maintenance requirements and system capacities for long-distance use.
Integrated Touring Capability and Storage
The 2026 Harley-Davidson® Street Glide® Limited includes a total luggage capacity of 5.05 cubic feet. Storage is distributed across hard saddlebags and the Tour-Pak®, providing enclosed space for travel gear. The design supports load distribution without significantly altering the motorcycle’s center of gravity.
The combination of storage capacity, fuel range, and integrated systems positions the model as a fully equipped touring platform. Each component is designed to operate within a coordinated system that supports extended riding durations.
Schedule a Test Ride Today
At Harley-Davidson® of Santa Clarita near Westlake, CA, riders can schedule a test ride to assess the technical capabilities of the 2026 Harley-Davidson® Street Glide® Limited. A test ride allows direct evaluation of the Milwaukee-Eight® VVT 117 engine output and the 6-speed transmission response across different speeds. It also provides an opportunity to interact with the Skyline™ OS interface, the 12.3-inch display, and integrated navigation features. Riders can observe the function of braking systems, traction control, and cornering enhancements under controlled conditions. Scheduling a test ride offers a structured way to examine how the motorcycle’s systems operate together during actual use.